1. What is the home position?
The home position is the position of all three axis' X,Y,Z by movement to the limit switch after pressing HOME button on the dsp hand control.
2. What is the start point or origin point?
2. What is the start point or origin point?
The starting or origin point is the position of the center of your router bit or cutting tool by starting the work in process. You can adjust origin point in your toolpath software. This is the point of origin on your material where you have to zero all axis' to start your work.
3.Unable to move X,Y or Z axis but display reads: Change Values?
Troubleshooting
- Check both ends of data cable if there is a good connection. First check data cable connection to dsp if screws are tightened and the end where the cable connects in the control box. Maybe unplug and plug all back in.
- check the connections in the black connector boxes, for each axis. Connector boxes for "x & z" under z head or top cover and for y under left side cover. Sometimes the wires may loosen with movement.
Now, look at the lights on the drivers in the control box....
* Red, then green and remains green = all is in order for operation
* Red, green when driving BUT an ERROR is detected, the light changes to red. STOP operation and reset machine (switch off and on again) check the lights on the drivers.
*If the light goes green again, there is only an error in the wiring. Check all cables connections again.
*When the lights stay red then the drivers need replacement
Troubleshooting
- Check both ends of data cable if there is a good connection. First check data cable connection to dsp if screws are tightened and the end where the cable connects in the control box. Maybe unplug and plug all back in.
- check the connections in the black connector boxes, for each axis. Connector boxes for "x & z" under z head or top cover and for y under left side cover. Sometimes the wires may loosen with movement.
Now, look at the lights on the drivers in the control box....
* Red, then green and remains green = all is in order for operation
* Red, green when driving BUT an ERROR is detected, the light changes to red. STOP operation and reset machine (switch off and on again) check the lights on the drivers.
*If the light goes green again, there is only an error in the wiring. Check all cables connections again.
*When the lights stay red then the drivers need replacement
4. Error message X hard limit
Select & press on machines’ DSP hand control:
MENU - SYSTEM SETUP – “Configure parameters”
When unable to select menu, press DELETE.
Now, MENU - SYSTEM SETUP – “Configure parameters”
press “OK” on language
Do you need to save power off? ok to choose others deny
press OK
Scroll to the only question about hard limit:
“Is there the hard limit sensors?” select to answer BUT
it skips to the next question, press CANCEL"
It is in traditional manual mode?” Select OK for traditional mode"
press OK
To change Setup – Toolcover Disable – Dustcover Disable
Press Toolcover disable The machine will power off to restart.
5.solving OVER LIMIT error
When OVER LIMIT in X, Y or X & Y, check dimension in toolpath settings for X, Y or both X & Y.
Troubleshooting
- Your design requires a larger area to complete than the working area available. Please check the dimensions of your design.
- Your laser head is not in the correct position in order to start from your origin point. You could move your laser head manually to another position and proof your point of origin in your design.
OVER LIMIT error
This error message means that the router has insufficient working area to complete your design. The error will inform you whether your design error is in + or - direction of the axis'
6. CNC Router with ballscrew in x & y axis'
In operation mode, with all lights green, it should not be possible to move or push the gantry by hand. If this is possible, there is usually an error in connection between motor and ballscrew.
Troubleshooting Check the connectors
- Check both ends of data cable if there is a good connection. First check data cable connection to dsp if screws are tightened and the end where the cable connects in the control box. Maybe unplug and plug all back in.
- check the connections for "x & z" behind the gantry cover and for y under the table right at the end. Sometimes the wires may loosen with movement.
Repeat steps above for checking the lights on the drivers in the control box.
In operation mode, with all lights green, it should not be possible to move or push the gantry by hand. If this is possible, there is usually an error in connection between motor and ballscrew.
Troubleshooting Check the connectors
- Check both ends of data cable if there is a good connection. First check data cable connection to dsp if screws are tightened and the end where the cable connects in the control box. Maybe unplug and plug all back in.
- check the connections for "x & z" behind the gantry cover and for y under the table right at the end. Sometimes the wires may loosen with movement.
Repeat steps above for checking the lights on the drivers in the control box.
Samples:
没有评论:
发表评论